mrmike
12-02-2004, 11:54 AM
First, let me commend all the folks at Stainless Works / Classic Autoworks for a wonderful experience. Everyone from the owner to the office staff was extremely helpful and accomodating.
The GTO was outfitted with headers, RT high flow cats, and a 3" exhaust built to my specification. The changes were proposed as an alternative to their chambered muffler setup, which is more along the lines of a full race muffler with commensurate increase in volume. Al Noe suggested the muffler design, and I handed him the keys.
The volume is right on the money for me. Modestly louder than a fully broken in stock system, but nothing that's going to get me a ticket or dirty looks from the neighbors. I can tell it suits me well, because as I drove it for the first time, I couldn't decide if it was too loud or not loud enough. Hmmmm. Must be just right.
The tone is very pleasing to me. A deeper, more pronounced rumble than stock. Accelerating, it has a more definite pitch to it, but extremely even throughout the RPM range. No "hot spots" at certain RPM or load conditions. Cruising with the windows up, you can tell it's there, but no hint of "drone." I didn't have to raise the radio volume or speak any louder than normal. There's a tad more sound from the engine bay, which is normal for headers vs. cast iron manifolds. However, when I stand on it, it commands your attention, but never gets "splatty" or out of control. When pulling in to pick up a pizza, one bystander commented: "I heard ya comin', nice car."
Tech wise, I need a tune now. Average O2 voltage is up almost 200 millivolts. Nearly 600 mV at cruise. Definitely rich, as expected. The battery was disconnected for the install, but I'm not sure if that resets the PCM by itself. Idle is a bit faster, with injector duty cycle at 3% against original 2%. Oddly, coolant temp is up about 3-4 degrees at speed. Hmmmm. Update after a complete drive cycle.
The rich mixture and improved booty squish tell me the system is doing exactly what it's supposed to.
All in all, I couldn't be happier. Al has every intention of making the system available to the public, and I can unhesitatingly recommend Stainless Works for their fine workmanship and first class customer service.
Apologies for the scanned photos. They will be replaced ASAP. Sound clips forthcoming as soon as I get the chance to record them.
The GTO was outfitted with headers, RT high flow cats, and a 3" exhaust built to my specification. The changes were proposed as an alternative to their chambered muffler setup, which is more along the lines of a full race muffler with commensurate increase in volume. Al Noe suggested the muffler design, and I handed him the keys.
The volume is right on the money for me. Modestly louder than a fully broken in stock system, but nothing that's going to get me a ticket or dirty looks from the neighbors. I can tell it suits me well, because as I drove it for the first time, I couldn't decide if it was too loud or not loud enough. Hmmmm. Must be just right.
The tone is very pleasing to me. A deeper, more pronounced rumble than stock. Accelerating, it has a more definite pitch to it, but extremely even throughout the RPM range. No "hot spots" at certain RPM or load conditions. Cruising with the windows up, you can tell it's there, but no hint of "drone." I didn't have to raise the radio volume or speak any louder than normal. There's a tad more sound from the engine bay, which is normal for headers vs. cast iron manifolds. However, when I stand on it, it commands your attention, but never gets "splatty" or out of control. When pulling in to pick up a pizza, one bystander commented: "I heard ya comin', nice car."
Tech wise, I need a tune now. Average O2 voltage is up almost 200 millivolts. Nearly 600 mV at cruise. Definitely rich, as expected. The battery was disconnected for the install, but I'm not sure if that resets the PCM by itself. Idle is a bit faster, with injector duty cycle at 3% against original 2%. Oddly, coolant temp is up about 3-4 degrees at speed. Hmmmm. Update after a complete drive cycle.
The rich mixture and improved booty squish tell me the system is doing exactly what it's supposed to.
All in all, I couldn't be happier. Al has every intention of making the system available to the public, and I can unhesitatingly recommend Stainless Works for their fine workmanship and first class customer service.
Apologies for the scanned photos. They will be replaced ASAP. Sound clips forthcoming as soon as I get the chance to record them.