Rearend Removal, illustrated - Page 2 - Pontiac GTO Forums: Pontiac GTO Forum
NewAge GTO Forums
 


» Auto Insurance
» Featured Product
Wheel & Tire Center

Go Back   Pontiac GTO Forums: Pontiac GTO Forum > GTO Tech > Transmission/Driveline Tech

Newagegto.com is the premier Pontiac GTO Forum on the internet. Registered Users do not see the above ads.
Reply
 
Thread Tools
Old 11-26-2017, 12:39 PM   #16
@project_vitamin_b5
Junior Member
 
Join Date: Nov 2017
Location: Southern California (Left Coast)
Posts: 1
reviving this old thread, like i'm reviving my old bushings.

Quote:
Originally Posted by mechanic58 View Post
Ok, I have been threatening to do this for a longtime, so here it is finally. A few weeks ago I ordered a set of 3.91s and a Harrop cover for my GTO. I decided that I was going to do a step by step how-to on the rearend removal and eventually the gear installation.

Pic of the car on jackstands, exhaust already removed:



Here is a pic of the tools you will need, a rachet with an 18mm socket, a medium sized adjustable wrench (or an 18mm wrench, I didn't have one handy), a 15mm wrench, a 17mm wrench (and another one to use as a cheater), another rachet with short extension and a 13mm, 14mm and a 15mm DEEP socket, an 8mm allen and a 5mm allen:



You will also need a foor jack and some jack stands.

In this pic, you can see the torx head bolts on the pinion flange. I do not know what size these are exactly, but a 12 point 14mm socket it fits it perfectly. Works good. You will have to remove all 6 of these bolts. 3 have the torx heads and the other three are 18mm with locking nuts on the back side. The center support for the driveshaft has two 13mm bolts. Once all the bolts on the pinion flange are removed and the center support mount bolts, the entire shaft can be removed. You have to wrestle with it a bit to get it past the nipple on the pinion gear, but it'll come. You need to force it forward as much as it will go once its unbolted from the pinion flange.


Here are the forward (upper) mount bolts. There are two, they are 17mm. It is easier to get to them after the driveshaft has been removed. I used a regular 17mm wrench with an 11/16 doubled on it as a cheater.



There are a total of FOUR of these bolts on top of the rear subframe. The rear upper two can't really be seen until you unbolt the rear mount and let the entire assembly down. Then you can get to them, also 17mm. I used the same double wrench technique to get them loose. You have to have all four of these bolts out and the four bolts that hold the rear mount in place in order to get the rearend out. There's also a vent pipe up on top that you will have to disconnect. Below is a pic of the rear mount, the four bolts are 13mm:



Next, you have to remove the antilock brake sensors and unbolt the half shafts from the stub axles. The ABS sensors have a single 5mm allen holding them in and the half shaft bolts are 8mm allens.


Now, once you have all this unbolted you can easily remove the rearend. Keep in mind that you will need to keep it supported on a floor jack while unbolting the mounts. I unbolted the half shafts and all the other stuff first, then did the mounts last. Unbolt the forward upper mounts first, then the rear mount, then you can let it down to get to the top rear mount bolts. Once they are out, it'll come on out. This job took me 45 mins from start to finish and that included removing the exhaust.


PM me if you have any questions.
Not to bring up an old thread for no reason, but I just got started on installing the ESMK and found this thread. I'm actually a visual person, so the photos would help. The only thing is, that they are not loading. Instead I am seeing boxes stating that I need to updated my account for 3rd party hosting. Does anyone have any of these photos readily available? I also tried logging into photobucket, have had no luck there either. Thank you in advance for any help.
@project_vitamin_b5 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Sponsored Links
Advertisement
 
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Powered by vBadvanced CMPS v3.2.2

All times are GMT -5. The time now is 11:50 AM.



Powered by vBulletin®. Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.